FANDOM


Script error
.460 Rowland
Type Pistol
Place of origin United States
Production history
Designer Johnny Ray Rowland
Produced 1998 – Present
Specifications
Bullet diameter .451 in (Bad rounding hereScript error mm)
Case length .957 in (Bad rounding hereScript error mm)
Overall length 1.275 in (Bad rounding hereScript error mm)
Primer type Large pistol
Ballistic performance
Bullet weight/type Velocity Energy
80 gr (Bad rounding hereScript error g) 3,050 ft/s (Bad rounding hereScript error m/s)1,680 ft·lbf (Bad rounding hereScript error J)
180 gr (Bad rounding hereScript error g) JHP1,560 ft/s (Bad rounding hereScript error m/s)1,000 ft·lbf (Bad rounding hereScript error J)
230 gr (Bad rounding hereScript error g) JHP1,340 ft/s (Bad rounding hereScript error m/s)930 ft·lbf (Bad rounding hereScript error J)
230 gr (Bad rounding hereScript error g) FMJ1,340 ft/s (Bad rounding hereScript error m/s)930 ft·lbf (Bad rounding hereScript error J)
260 gr (Bad rounding hereScript error g) FMJ1,150 ft/s (Bad rounding hereScript error m/s)770 ft·lbf (Bad rounding hereScript error J)
Test barrel length: 5.5 in
Source(s): .460 Rowland LLC

The .460 Rowland is a proprietary cartridge which attains true .44 Magnum level velocities when fired from a number of popular semi-automatic pistols, revolvers, and rifles.Script error[citation needed] The cartridge was designed and developed by Mr. Johnny Ray Rowland, host of "The Shooting Show." After first developing the new cartridge, Mr. Rowland worked with Starline Brass to finalize commercial production of the brass and later with Clark Custom Guns to develop the first commercially available .460 Rowland Conversions for specific versions of the M1911.[1] First production shipments of ammunition and conversions were made through these associations in 1998. Script error[citation needed]

DesignEdit

The .460 Rowland case is approximately 1/16" longer than a conventional .45 ACP case but the overall cartridge length is the same, the bullet is simply seated deeper. The purpose of the extended case length is to prevent the high pressure .460 Rowland from being chambered in a standard firearm chambered for the low pressure .45 ACP. This is similar to the relationship between the .357 Magnum and the .38 Special.

There are two key elements to the .460 Rowland concept. The first is a sharp increase in cartridge maximum pressure over the .45 ACP and .45 Super. Maximum Average Pressure is: 45 ACP (21,000 PSI), .45 ACP +P (23,000 PSI), .45 Super (28,000 PSI), .460 Rowland (40,000 PSI). The second is to damp or reduce the velocity of the slide in converted autoloading pistols to manageable levels. The first delivers magnum level performance and the second allows the cartridge to be easily and reliably fired from compact, light weight, high capacity, autoloading pistols.

ConversionsEdit

File:460Rowland M1911.jpg

The increase in slide velocity over a standard .45 ACP, or even a .45 Super round, cannot be properly controlled with an increase in recoil spring rate alone. Autoloaders properly converted to fire the .460 Rowland Cartridge require a compensator or a ported barrel to insure reliable, long lasting, operation. This fact not withstanding, there continues to be customer demand for a "Stock-Looking" .460 Rowland Conversion; however, any effort to answer this demand is thus-far not supported by the Inventor. Mr. Rowland still maintains that a properly designed .460 Rowland Conversion requires an effective compensator to momentarily delay slide action until the very high pressures developed by his cartridge dissipate to more manageable levels. Without this compensation, slide or frame failure will result over time and reliability will suffer in the short term. Script error[citation needed]

A properly compensated .460 Rowland Conversion will accurately and reliably fire .45 ACP, +P and .45 Super cartridges.Script error[citation needed] The shorter .45 casings are held in position by the gun's extractor in much the same way as many highly accurate revolver cartridges are held in their long chambers by moon clips. Accuracy and power do not suffer as a result.Script error[citation needed]

High qualityScript error[citation needed] 1911 auto-loading pistols are manufactured by many different companies and tolerances vary with each manufacturer. As a result, adjusting recoil spring tensions and identifying specific magazines that works best in each individual gun have always been necessary to insure optimum performance from this 112 year old design. These same considerations are no less important when converting these guns to fire .460 Rowland cartridges. Once installed, tested and adjusted in this manner, a 1911 / .460 Rowland Conversion will shoot .45 ACP, +P, Super and .460 Rowland cartridges accurately and reliably without ever having to revert to the factory barrel. Springfield XD / XDm, Glock-21 and Glock-30 auto-loaders and the Sig-Sauer Model 220 are all made by a single manufacturer so similar adjustments are not often needed when these guns are converted to fire the .460 Rowland.[2]

The Ruger Blackhawk and Smith & Wesson Model 25/625 can also be chambered to fire the .460 Rowland. These conversions require deepening the chambers, and is effectively permanent unless the owner has a replacement cylinder fitted. For several years Dan Wesson also made a revolver specifically made for the .460 Rowland, which would also chamber .45 ACP, .45 Super and .45 Winchester Magnum, as does the Smith & Wesson Model 25/625. Both guns use moon clips and are very accurate fire arms. [Citation; Mr. Johnny Ray Rowland & .460 Rowland LLC]

See alsoEdit

ReferencesEdit

  1. Script error
  2. Script error

External linksEdit

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.